![]() ![]() The fitting routine will stop and warn the user if the Solver is not i nstalled. Pumping_StepDrawdown-2019.xlsm workbook requires that the Solver is i nstalled and the workbook is not opened from within a zip file. This workbook and other workbook applications are better used on local drives instead of a network drive. Pumping_StepDrawdown-2019.v3.xlsm and explanatory PDF can be downloaded with the following link. ![]() Figure 2.- OUTPUT page in Pumping_StepDrawdown-2019.xlsm with data from well DW20. Step along with measured and simulated drawdowns. Well efficiency is reported at the end of each Screen length adequately approximates aquifer thickness. Average hydraulic conductivity is reported by assuming Estimated transmissivity, T, and well-loss coefficients, B ´ Well-loss coefficients B ´ and C can beĪdjusted manually with scroll bars in cells H35 and H36 or regressed with the “FIT”īutton in cell H32 (Figure 2). Ignore outliers in the flow-normalized drawdown plot by estimating T with scrollīar in cell H34 on the OUTPUT page. Fit between straight line and plotted data can be refined visually to Data setsĪre converted to drawdowns in preferred units of analysis and estimates of T, B ´,īutton. Step-drawdowns, recoveries, and flow ratesĪre plotted on a cartesian plot and a flow-normalized drawdown plot. Specified as depth to water or water level above the transducer. Series of antecedent, pumping, and recovery water levels in the pumped well are Step-drawdown data can be interpreted in the workbook, Pumping_StepDrawdown-2019.xlsm toĮstimate transmissivity and well-loss coefficients (Figure 2). The aquifer, B(t)Q(t), and linear well loss, B ´Q, were combined in the term BQ. This formulation differs from Rorabaugh (1953), where drawdown in Step-drawdown test to the current time ( t).Īnd CQ². Solutions that evaluate all pumping rates from the beginning of the Is solved with superimposed Theis ( 1935) Drawdown in the aquifer and well losses are simulated with the equation: Solution and well losses have linear and non-linear components (Rorabaugh,ġ953). The analytical model assumes that the aquifer can be Transmissivity of the aquifer likely was reduced by dewatering transmissive fractures. The flow-normalized drawdown plot also makes other departures between measured drawdowns and analytical model apparent such as the departure between measured and simulated slopes at highest pumping rate of 600 gpm (Figure 1, s/Qstep>0.7). These observations are eliminated from the regression by assigning weights of 0 to minimize their effects on estimates of well-loss coefficients. These anomalies result primarily from the analytical model not simulating wellbore storage. Transmissivity can be adjusted manually to best explain late-time drawdowns during each step, while visually ignoring anomalies from unsteady flow rates and wellbore storage. Transmissivity estimates are improved with the flow-normalized drawdown plot, because effects of transmissivity on drawdowns are isolated from well-losses (Figure 1). ![]() Were improved in the workbook, Pumping_StepDrawdown-2019.xlsm. Well-loss model and parameter estimation techniques Measured s/Qstep depart from straight lines at the beginning of each stepĭrawdowns were analyzed with a flow-normalized drawdown plot in a previouslyĪnd Kuniansky, 2002). Separately because of non-linear, well losses. T = 35.3 / Slopein field units of ft²/d, ft, and gpm. Slope (T/L²) estimated from flow-normalizedĮquation for transmissivity simplifies to, Q CONVERT converts flow to consistent units, e.g. T = 2.303 Q CONVERT / 4 / π / Slope or 0.1832 Q CONVERT Interpretation differs from Cooper-Jacob ( 1946) because discharge is incorporated in the estimated slope. Line, where transmissivity is inversely proportional to the slope ( Lee,ġ982). Transformed data theoretically should plot in a straight Figure 1.- Example of transformed drawdown (s) and flow-rate (Q) data and interpreted slope of s/Q that is inversely proportional to transmissivity. Drawdown ( s) and flow-rate ( Q) data are transformed by plotting drawdowns divided by flow rates ( s/Qstep) against flow-weighted, dimensionless times (Figure 1). The 2019 workbook accounts for linear and non-linear well losses while using graphical techniques to better estimate transmissivity ( Odeh and Jones, 1965). Transmissivity and well-loss coefficients can be estimated from step drawdown data with the workbook, Pumping_StepDrawdown-2019.xlsm. Pumping, during each step, and during recovery so that drawdowns can be Greater discharge rates are pumped during subsequent steps, where three to fiveĭischarge rates typically are tested. Water levels to change minimally at the end of each step ( Halford and Pumping rates are constant during steps which are of sufficient A step-drawdown test is a single-well test that isįrequently conducted after well development to determine well efficiency and correctly ![]()
0 Comments
Leave a Reply. |